Structural Fire Damage Cleaning in Bishop, TX
With the wallboard torn out, what is left is a skeleton of black studs, scorched rafters and smoke-stained block. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Bishop who clean the framing, masonry and steel itself.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Check the paperwork yourself and ask if their process lines up with IICRC S700.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Bishop are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Structural Cleaning Services From Rafters to Slab
This is not contents cleaning and it is not debris haul-out. It is the work done on the wood, block, brick and steel that hold your house up.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Crawlspaces get the same treatment on a smaller, dirtier scale: floor joists, sill plates and the underside of the subfloor are probed, blasted where needed and sealed. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Have the contractor explain the method they plan for each part of the house. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Plan for containment, because blasting throws soot and media into every corner it can reach. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask what the plan is to shield the undamaged rooms, floors and glass.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Bishop. It costs nothing to call.
Call +1-833-336-1630The Path From Charred Framing to Sealed Wood
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
They test each stud, joist and rafter with an awl, tag it, and flag anything doubtful for an engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
Our basement fire blackened the block walls and the steel beam over the family room. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. The basement smells normal again, even closed up.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
They probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice leaves no media behind and works well near wiring, but the equipment is noisy and the job usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. An encapsulating sealer traps what is left so the odor does not seep back through the finished walls. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Spalling or cracked masonry is a structural question for a mason or engineer.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Bishop and Beyond
Calls come in from all over Bishop and nearby towns, from older homes with solid lumber framing to newer builds with engineered trusses and I-joists. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Get the bones cleaned before anyone hangs new drywall.
